Electrical Connections
- Trailer Connectors keyboard_arrow_right
- Air Products keyboard_arrow_right
- Terminals & Connectors keyboard_arrow_right
- Wire & Cable keyboard_arrow_right
- Support & Protective keyboard_arrow_right
- Switches & Electrical Assemblies keyboard_arrow_right
- Battery Connectors & Cables keyboard_arrow_right
- Kits & Tools keyboard_arrow_right
Company
- Company Profile keyboard_arrow_right
- Careers keyboard_arrow_right
- Case Studies keyboard_arrow_right
- Contact Us keyboard_arrow_right
- Grote News keyboard_arrow_right
- Press Releases keyboard_arrow_right
- Trade Shows & Events keyboard_arrow_right
- Quality keyboard_arrow_right
- Star Safety Technologies by Grote keyboard_arrow_right
Customer Information
- Searching by:
- Products
- Informational
- Interchanges
Knowledge Base
Installation
- I would like installation instructions on the 53962 light only, grommet seems fine. This looks like a snap-in light, I just need to know how to go about doing it.
- How do I separate the red lens from the white housing in a Grote 5218 trailer light in order to change a burnt out bulb?
- I always seem to struggle when installing a 6 ½ inch oval lamp. Should you install the gasket to the vehicle first then the lamp? Is there some kind of trick to ease installation?
- I am looking for installation wiring diagram for 77931
- How do I install the Grote 64930 Par 36 Utility Lamp with only one wire coming out of the light?
- Were to find a install instruction for 78473 light bar? Or trouble shooting. Unit just blinks on the pad does not light up lights on bar.
- How do I install Grote’s 4×6 high / low beam led headlight 94401-5?
- How should I change the wiring for turn signal switch 48272 to make it appropriate for a 6v. Positive Ground vehicle?
- How do I install the 77003 LED Light bar?
- How do I install Grote’s replacement LED Headlights?
- How do I attach my LED Light Strip?
- How do I install the 64J31 Light Bar?
- How do I install the 64J21 Light Bar?
- How do I install the 64J11 Light Bar?
- I have 2 per-lux 200 T lights but I don’t have the swivel part that goes between the bumper and the light, allowing the light to be aimed. Where can I get some?
- When a customer up-grades his vehicle turn signal lights to LED can he correct the flashing sequence by changing the flasher to LED flasher or does he have to install a module?
- I am installing a new 5218 brake light and a new 9242 rubber grommet in an aluminum trailer. Can I have the directions on what way and what direction these two item are to be installed?
- I just changed all of my lamps to LED and now my Flasher doesn’t work, what is the problem?
- I just changed my Rear Turn Lamps to LED and now my Flasher blinks too fast. How do I slow them back down?
- 53963 won’t strobe and have power to them
- Wiring diagram/ installation instructions for LED marker part # 78163
- I purchased several LED Work lamps and none of them are working.
- I would like to connect several of the XTL strips together.
- Can I cut the XTL strips?
- I would like to make my Brake Lights strobe when I apply the brake.
- What do the letter Codes for Back Up Alarms stand for? E.g…. A, B, C etc.
- I purchased your LED Headlamps and when I have my daytime running lamps on, they flicker.
- What hole size do I need to mount the DOT - Micronova lamps?
- What does Self Grounding mean on the 47012 & 47013?
- I need an ignition switch that has spring return to ON, and for Glow Plug.
- Which is best to use for bulb and socket (such as 1156/1157 bulb and socket) to prevent corrosion and ensure long term reliability? Ultra Seal or dielectric grease or something else?